Member II
Trying tp get on board air on my 02 TJ Sport. Always want my installs to be clean so this is really tough. Anyone have any suggestions let me know. I tried the plate under the brake booster but it's just too tight.
What Did You Do With Your Rig Today?
- Thread starter iamout
- Start date
Explorer I
What on board air system are you trying to install? I have an ARB and I was able to install it near the brake booster. Ill get photos for you in moment.
Explorer I
Fly_hippie Here are a few photos on how I fit my ARB near the brake booster. Its been in that exact spot for 5-6 years now. Not once single issue. I thought by now I would have burned it up being in the engine bay. 
Enthusiast III
Installed new headlights on my 2001 F350 7.3
Went from zero visibility to WOW !!!
Must say it did not go to easy, but it got done.
Went from zero visibility to WOW !!!
Must say it did not go to easy, but it got done.
Enthusiast III
Same setup. The plate under the brake booster is a good location for an ARB compressor:Fly_hippie Here are a few photos on how I fit my ARB near the brake booster. Its been in that exact spot for 5-6 years now. Not once single issue. I thought by now I would have burned it up being in the engine bay.
I use the gallon milk jug cap (perfect friction fit) to keep out debris. The compressor is wired to an sPOD. The air hose reaches all five tires.
Enthusiast III
- 770
- First Name
- Allan
- Last Name
- Overby
- Member #
-
24919
- Ham/GMRS Callsign
- KN6DXV
today I bonded the Subaru and put LP Adventure rockslides on. everything was bonded, all doors, rear hatch and hood double bonded
Attachments
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
That’s a great price for the bond straps!
what was your reason for doing that, RFI in your radio gear?
Member III
Purchased a used shell a couple months ago, had it painted to match the truck. Made a rack from 80/20 1020 1"x2" and 1"x1" with 2"x1/4" aluminum sides. Added an ARB awning to the zr2 this morning.
Now I don't need to carry a free standing awning In the back of the truck anymore.
Now I don't need to carry a free standing awning In the back of the truck anymore.
Member III
- 2,771
- First Name
- Rolando
- Last Name
- Nispiros
- Member #
-
17011
- Ham/GMRS Callsign
- KN6JJS
Member III
Last night we went to the top of one the local buttes so my wife could get some sunset and comet shots.
The first two are from my phone, the last three (the good ones) are done by my wife.
The first two are from my phone, the last three (the good ones) are done by my wife.
Enthusiast III
- 770
- First Name
- Allan
- Last Name
- Overby
- Member #
-
24919
- Ham/GMRS Callsign
- KN6DXV
Trying to get as much ground plane as possible. When i transmit the more ground plane the stronger my signal will be. Hf signal needs as much ground plane as you can give it. So if i run 100watts, only 50 to 75watts may actually get out. So im increasing my chances of better performance.
Enthusiast III
- 770
- First Name
- Allan
- Last Name
- Overby
- Member #
-
24919
- Ham/GMRS Callsign
- KN6DXV
Added the Mopar 2 inch lift and Falken WILDPEAK A/T3W tires (255/80R17)
On Monday, I will pick up the ARB Twin High Performance 12 Volt Portable Air Compressor
Next up, winch, armor, tire carrier, seat delete, kitchen, roof rack, RTT.
On Monday, I will pick up the ARB Twin High Performance 12 Volt Portable Air Compressor
Next up, winch, armor, tire carrier, seat delete, kitchen, roof rack, RTT.
Advocate III
- 5,584
- First Name
- Michael
- Last Name
- Rose
- Member #
-
20990
- Ham/GMRS Callsign
- W7FSB
- Service Branch
- US ARMY Retired
yesterday the “Adventure Machine” developed
the notorious steering whine. I decided long ago I was going to convert over to a Saginaw power steering system for better pressures, steering response and reliability. So I went and stole the power steering pump, winch and Auxiliary Lights
from my Ram. Today I start the Saginaw swap and install my winch. Pics to fallow.
the notorious steering whine. I decided long ago I was going to convert over to a Saginaw power steering system for better pressures, steering response and reliability. So I went and stole the power steering pump, winch and Auxiliary Lights
from my Ram. Today I start the Saginaw swap and install my winch. Pics to fallow.
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
You might be surprised by the small difference on the transmit results. Receive is definitely going to benefit. My rig is a police package Tahoe. It’s got bonding straps everywhere.
Enthusiast I
Member III
Temporarily traded my Tahoe for my dad's 2011 RAM 1500. Reason being, on the way to work Friday night gauge cluster in the Tahoe decided to turn off. Smacked it once and it worked again for about a minute and cut off again. Cluster is currently on it's way to Wisconsin. It'll be rebuilt and have LED backlights and a transmission temp gauge added in.
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
How well does a dodge power steering pump fit on a Ford Bronco ? How will you install the winch on the Bronco with the stock bumper ?
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
