Member II
- 2,268
- First Name
- Mark
- Last Name
- Tebo
- Member #
-
12262
- Service Branch
- US Army Retired
Installed a 23 Zero Peregrine Awning to the Prinsu
What Did You Do With Your Rig Today?
- Thread starter iamout
- Start date
Traveler III
Dang, that's a sweet tent trailer! Never seen anything like that before.
Member II
- 2,268
- First Name
- Mark
- Last Name
- Tebo
- Member #
-
12262
- Service Branch
- US Army Retired
Explorer I
- 3,680
- First Name
- Brian
- Last Name
- McGahuey
- Member #
-
23711
- Ham/GMRS Callsign
- GMRS WRMV941
Swapped out my camshaft position solenoid this morning, and cleaned the throttle body. Butt-dyno says it's definitely a bit smoother at idle, and definitely smoother on acceleration now.
Enthusiast III
Finished making these puppies tonight, I'll paint and mount em tomorrow then test em
Member II
Influencer I
Enthusiast III
Just a couple of improvements to my 2004 TJ Rubicon this past weekend (with the help of my brother):
Teraflex 1” body lift;
Brown Dog 1” rise engine mounts;
Teraflex BellyUp skid plate with Rubicon compressor mount;
Novak transfer case shifter cable assembly;
Metalcloak rear upper and lower control arms;
Metalcloak JK DuroSpring jounce bumpers (front bumpers in the rear cups).
This weekend having the NV-3550 5-spd trans rebuilt.
Following the trans rebuild, replacing the radiator. 15 years on the oem plastic tank, a little preventive maintenance after watching Michael’s YouTube video when his radiator Code 3’d itself on the trail.
Teraflex 1” body lift;
Brown Dog 1” rise engine mounts;
Teraflex BellyUp skid plate with Rubicon compressor mount;
Novak transfer case shifter cable assembly;
Metalcloak rear upper and lower control arms;
Metalcloak JK DuroSpring jounce bumpers (front bumpers in the rear cups).
This weekend having the NV-3550 5-spd trans rebuilt.
Following the trans rebuild, replacing the radiator. 15 years on the oem plastic tank, a little preventive maintenance after watching Michael’s YouTube video when his radiator Code 3’d itself on the trail.
Last edited:
Influencer I
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
Does it have wind noise that can be heard from inside the rig or is that what looks like an air dam keeping it quite ?
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
Enthusiast III
As soon as I get her back from the shop doing the clutch and transmission mount exhaust hanger cut (~1” shorten) & weld. Maybe a rear coil bracket relocation...
Member II
- 2,268
- First Name
- Mark
- Last Name
- Tebo
- Member #
-
12262
- Service Branch
- US Army Retired
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
Member III
Installed a new brush guard and replaced the torn steering wheel with a new one
Member II
Installed the Midland MXT275 today.
And Comet CA-2X4SR antenna.
Also had time to install auxiliary accessory switches in a mount I fabricated early this week.
And Comet CA-2X4SR antenna.
Also had time to install auxiliary accessory switches in a mount I fabricated early this week.
Member II
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
Influencer II
Took a small anglegrinder to the 14 small remaining screws that were left after I removed the roofrails a while back.
I also covered up the exposed metal with some paint and am planning on getting the roof resprayed either gloss or matt black next year as I also want to remove the antenna and weld that hole shut and fit a couple strips of aluminium to where the roofrails used to be.
I want a cleaner look to my car as I want it to be different from all the other 1st generation Hyundai Tucsons on the road.
I also covered up the exposed metal with some paint and am planning on getting the roof resprayed either gloss or matt black next year as I also want to remove the antenna and weld that hole shut and fit a couple strips of aluminium to where the roofrails used to be.
I want a cleaner look to my car as I want it to be different from all the other 1st generation Hyundai Tucsons on the road.
Last edited:
Member III
- 2,827
- First Name
- Jim
- Last Name
- covey sr
- Member #
-
16986
- Ham/GMRS Callsign
- none - BREAKER BREAKER HAND HELD CB AND WALKIE TALKIE
Your the only one who will ever see the difference. Beauty is in the eye's of the beholder !
