What Did You Do With Your Rig Today?

[roots66]

Mine aren’t readily visible either. Until you drop a flashlight or tool under the hood, and it doesn’t come out the bottom.

Been there, done that, but with either a bolt or socket.

 

[roots66]

In the middle of installing a front and rear camera for my Tacoma, I can switch them any time I want.

I tried to install a rear camera and discovered after everything else was done, the video cable was about 2' too short.

 

[J.W.]

Spent more time than I should have to get the map lights out of the headliner so I can install some new LEDs.

 

[eagle_A40]

In the middle of installing a front and rear camera for my Tacoma, I can switch them any time I want.View attachment 125368

I'm doing the same thing. The A / V cables are run, but cameras are not mounted. I'll have to come up with a camera mount to affix it to the under-side of the front bumper center grill-guard bar.
For the rear camera, I'm waiting on material to build a rear bumper, then to install the camera.

 

[Captstout]

Mine aren’t readily visible either. Until you drop a flashlight or tool under the hood, and it doesn’t come out the bottom.

Been there. Lol

 

[eagle_A40]

Today, I used a L-bracket to attach the CB antenna to the tie-down rail in the front of the truck bed(passenger's side).

It matches the GMRS antenna bracket I installed a month ago on the driver's side.

 

[Sparksalot]

Been there, done that, but with either a bolt or socket.

It’s where all the 10mm sockets go to die!

 

[TerryD]

I added one of those cheap bolt on tire carriers to our new trailer that I'm hoping to make into a base camp trailer for us over the next year. Next is to enclose it with plywood temporarily to see if it's going to be as useful as I'm hoping or if we need to look at going with a larger trailer to start with. So far I haven't done anything that can't be easily undone.

 

[PaulH]

I set up my Staun tire deflators to 15psi. And, being the OCD person I am tested each on individually. Spent the better part of an hour airing down my spare and then back up and making adjustments till each was was spot on.

 

[Shamu]

I set up my Staun tire deflators to 15psi. And, being the OCD person I am tested each on individually. Spent the better part of an hour airing down my spare and then back up and making adjustments till each was was spot on.

Did the same prior to my latest trip. Those Staun deflators worked like a champ! Much easier than using a key.

 

[PaulH]

Did the same prior to my latest trip. Those Staun deflators worked like a champ! Much easier than using a key.

I also had bought the ARB tire deflator, but like the Staun's much better and will be sending the ARB back. It worked quickly, but the gauge on it is off by almost 4psi compared to my other gauges. The Stauns seem like the best way to go for me. No standing there bent over or kneeling in the mud either.

 

[smarthead]

For today will just clean the interior like really clean it.

 

[Jeepmedic46]

I started looking for shorts to my electrical issues after my headache Doctor appointment. Wires I checked were in good shape in my XJ. If not to cold and head isn’t pounding tomorrow will look some more.

 

[eagle_A40]

I removed the center section of the dash, to run a phone charging cable, and the front/rear trail camera power/video cable.
I drilled a hole in the upper dash tray and installed a nylon grommet to run the cables through.





I then ran the rear camera video cable along the truck frame to the rear bumper location and secured it with wire-ties. I'll be building a HD rear bumper in the near future and will make a mount for the rear camera. I also ran the front camera video cable under the hood, to behind the grill for when I install the front winch bumper w/trail camera.

Then I drove to the store for a six-pack, so my truck and I could celebrate our accomplishment.

 

[Jeepmedic46]

I removed the center section of the dash, to run a phone charging cable, and the front/rear trail camera power/video cable.
I drilled a hole in the upper dash tray and installed a nylon grommet to run the cables through.

View attachment 125595

View attachment 125594

I then ran the rear camera video cable along the truck frame to the rear bumper location and secured it with wire-ties. I'll be building a HD rear bumper in the near future and will make a mount for the rear camera. I also ran the front camera video cable under the hood, to behind the grill for when I install the front winch bumper w/trail camera.

Then I drove to the store for a six-pack, so my truck and I could celibate our accomplishment.

Looks good

 

[eagle_A40]

Looks good

Thanks, William.
When I drove to the store, the radio had no sound. I removed the radio bezel again and found that I had forgotten to plug in the power connector.

 

[Jeepmedic46]

Thanks, William.
When I drove to the store, the radio had no sound. I removed the radio bezel again and found that I had forgotten to plug in the power connector.

At least it was a quick fix

 

[eagle_A40]

At least it was a quick fix

Yes it was. The cold brews went down a little better after finding the self-inflicted problem.

 

[roots66]

More "work".

 

[kkriewald]

I removed the center section of the dash, to run a phone charging cable, and the front/rear trail camera power/video cable.
I drilled a hole in the upper dash tray and installed a nylon grommet to run the cables through.

View attachment 125595

View attachment 125594

I then ran the rear camera video cable along the truck frame to the rear bumper location and secured it with wire-ties. I'll be building a HD rear bumper in the near future and will make a mount for the rear camera. I also ran the front camera video cable under the hood, to behind the grill for when I install the front winch bumper w/trail camera.

Then I drove to the store for a six-pack, so my truck and I could celibate our accomplishment.

If you said so earlier I missed and apologize (don't have a lot of experience in forums), is that cross bar mount made by Ram Mounts?