Contributor I
I’m a new member so I figured I’d make a post about my camper and see what overland bound is all about! I wish I had started a thread or something when I started building the camper but if anyone has any questions just ask.
DIY teardrop
- Thread starter TacomaSparky
- Start date
Contributor I
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
Contributor I
I Ultra-Tow Stub Torsion Axles Pair, 1000-Lb. Capacity per Pair | Northern Tool + Equipment
I used these axles because they were cheap but hopefully I’ll upgrade them eventually. I haven’t taken it off-road yet but it does will on roads.
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
That’s cool. Mine uses the stock tube axle and leaf springs. I’ve got 11 years of travels on her, plus two trips to Wyoming. last year my daughter and I did part of the Enchanted Rockies Trail while pulling the rear. I’m thinking I’m probably pushing the edge of the envelope when it comes to washboard roads and such. On the other hand, I just hate driving on those anyway.
Last edited:
Contributor I
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
I used CPES on the bare wood. Hint, be sure you’re done cutting and trimming before you do it, the wood becomes rock hard. It’s also not a UV block, so I’ve got spar varnish on her. finally she stays in the garage unless out camping.
Boostpowered
Rank VI
Member III
Nice, i wish i were better at woodworking. Id have to build from sheetmetal if built one.
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
Boostpowered
Rank VI
Member III
Im opposite metalwork is easy to me, i cant cut wood straight to save my life.
Do you have a set of plans that you sued to build this? What kind of trailer did you use for the base?
Contributor I
I’ve kinda just been doing it by looking at thinks so there isn’t any plans for it unfortunately. The trailer was free from my grandma but I had to chop it down to a smaller size and weld it back together.
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
-
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
Enthusiast III
Contributor I
When I first built the camper I built a wall at about 6’ 2” but after going to overland expo east I’ve decided to redesign the rear wall.
Contributor I
The counter top and wall used to be where the walls are not stained
The new design allows me to have more leg room inside and I’ll be able to fit a dometic under the counter
Creator III
- 5,660
- First Name
- Jason
- Last Name
- Shelby
- Member #
-
6080
- Service Branch
- TN National Guard
I’m currently building a Turtlebackish style trailer using a 4x8, 4ft enclosed trailer.
@jeanklaudethejeep
@jeanklaudethejeep
Contributor I
Yeah I saw the thread and left a comment I think. I like the idea of using that camper but the hard part would be getting more ground clearance.
Creator III
- 5,660
- First Name
- Jason
- Last Name
- Shelby
- Member #
-
6080
- Service Branch
- TN National Guard
I seen your comment after I posted here, I’ll have enough ground clearance for what I’m willing to pull the trailer through. Approximately 24” on the body, 17 on the axle which is more than the Jeep with have because of the diff.
