Dfw area welder

  • HTML tutorial
Boostpowered

Boostpowered

Rank VI

Member III

4,879
Hunt county, TX, USA
First Name
Justin
Last Name
Davis
Member #

14684

Is there anyone on here in the dfw area that has a mig welder that can do my rock sliders? Ill have all the tubes pre bent but my welder is a flux core and i dont trust its welds on something structural like this. I can tack everything where i want it if that helps. I prefer someone who welds for a living but if you can stack dimes we can talk. Let me know availability and price, and location in private message.

Id prefer east dfw if possible or if anyone has a trusted welder they can guide me to that would work too.
 
Last edited:
Boostpowered

Boostpowered

Rank VI

Member III

4,879
Hunt county, TX, USA
First Name
Justin
Last Name
Davis
Member #

14684

Offroadnutz said:
I see people on craigslist advertising their services all the tme. Might be an option....
Click to expand...
Nah i dont want to be murdered over $100,and folks on craigslist tend to not answer my calls likely because i have a indianapolis cell #. if i cant find someone ill just drive down to mineola and use my dads mig. I figured someone here would know someone or be certified themselves and want to make some quick cash.
 
Downs

Downs

Rank V
Launch Member

Member III

2,827
Hunt County Texas
First Name
Joshua
Last Name
Downs
Member #

20468

Ham/GMRS Callsign
KK6RBI / WQYH678
Service Branch
USMC 03-16, FIRE/EMS
There's a few machine shops down here in Greenville that can probably do the work for you. FWIW I welded my sliders together with a flux core welder (Harbor Freight haha) and I can pick the whole side of the Jeep up with a high lift jack with no issue, never even had the welder overheat. They're bolted to the "frame rails" and to the pinch seam under the rocker panels everything else is welded. They've been bashed on a few rocks and are still good to go.

My previous 2 Jeeps also had homebuilt sliders that were built with cheap welders. They held up fine.

Go to town on it :)

Check out

White Hawk Machine and Tool on the west side of town off HWY 66 and Felt's Welding and Machine Shop on the north end of town on North Johnson Street.
 
Boostpowered

Boostpowered

Rank VI

Member III

4,879
Hunt county, TX, USA
First Name
Justin
Last Name
Davis
Member #

14684

Downs said:
There's a few machine shops down here in Greenville that can probably do the work for you. FWIW I welded my sliders together with a flux core welder (Harbor Freight haha) and I can pick the whole side of the Jeep up with a high lift jack with no issue, never even had the welder overheat. They're bolted to the "frame rails" and to the pinch seam under the rocker panels everything else is welded. They've been bashed on a few rocks and are still good to go.

My previous 2 Jeeps also had homebuilt sliders that were built with cheap welders. They held up fine.

Go to town on it :)

Check out

White Hawk Machine and Tool on the west side of town off HWY 66 and Felt's Welding and Machine Shop on the north end of town on North Johnson Street.
Click to expand...
Is your welder the old 90 amp or the newer 120amp? Ive got a newer one. Do use th hf wire or a better mfg?15821298374962032975588.jpg
 
Downs

Downs

Rank V
Launch Member

Member III

2,827
Hunt County Texas
First Name
Joshua
Last Name
Downs
Member #

20468

Ham/GMRS Callsign
KK6RBI / WQYH678
Service Branch
USMC 03-16, FIRE/EMS
90 amp and the first thing I did was toss the HF wire in the garbage and get a new spool, what little welding I did with the HF spool was a mess, no matter how I adjusted the unit I couldn't get a clean weld, apparently that's a common complaint with the unit is the spool that comes with it, is garbage.

I've burnt though a couple of spools by this point the current one I have in there is whatever brand Lowe's carries.
 
Boostpowered

Boostpowered

Rank VI

Member III

4,879
Hunt county, TX, USA
First Name
Justin
Last Name
Davis
Member #

14684

Downs said:
90 amp and the first thing I did was toss the HF wire in the garbage and get a new spool, what little welding I did with the HF spool was a mess, no matter how I adjusted the unit I couldn't get a clean weld, apparently that's a common complaint with the unit is the spool that comes with it, is garbage.

I've burnt though a couple of spools by this point the current one I have in there is whatever brand Lowe's carries.
Click to expand...
Did you do the dc negative conversion? That supposedly makes them weld like a hobart. No splatter. I planned on trying to tack weld everything into place and get it welded professionally but i suppose ill try and give it a good bead and see what happens, i know im not paying a welder $650 for it.
 
Longshot270

Longshot270

Rank V
Launch Member

Experimenter I

1,453
DFW, TX
First Name
Colby
Last Name
M
Member #

5160

Get some extra pipe and practice. Mig can be tricky but you'll get it figured out. Get a piece of scrap and cut notches to weld back up (and take notes). Test a variety of wires, amps and polarity to find what works. We used to butt weld two pieces of flat together and bend it over until it broke to see if we got the wild right.

I never got the hang of mig. My high school welding class only had one to share among 12 students and the rest of us used stick. I just didn't have the inclination to learn it back then because I wanted to get my projects done.

My little 110v stick welder does pretty good with some 3/16" 7018s though. I need to practice with the 6011s though.20200111_152507.jpeg20200125_103409.jpeg
 
Downs

Downs

Rank V
Launch Member

Member III

2,827
Hunt County Texas
First Name
Joshua
Last Name
Downs
Member #

20468

Ham/GMRS Callsign
KK6RBI / WQYH678
Service Branch
USMC 03-16, FIRE/EMS
I started on stick and moved to MIG later. Though these arent MIG welders.
MIG (or flux wire in this case) is like diving an automatic.

@Boostpowered i havent done any mods to mine. Just welded stuff with it. Theyd need to be conveted to DC since they are AC welders out of the box.
 
Jackedupoffroad

Jackedupoffroad

Rank 0

Contributor I

60
Plano, TX
First Name
Jack
Last Name
London
Boostpowered said:
Is there anyone on here in the dfw area that has a mig welder that can do my rock sliders? Ill have all the tubes pre bent but my welder is a flux core and i dont trust its welds on something structural like this. I can tack everything where i want it if that helps. I prefer someone who welds for a living but if you can stack dimes we can talk. Let me know availability and price, and location in private message.

Id prefer east dfw if possible or if anyone has a trusted welder they can guide me to that would work too.
Click to expand...
I'm a little late to the party, but Id be happy to weld them up for you if you havent gotten them done already. . Located in a Plano. Not sure when with the current state of the nation, but when things clear up I'd be happy to make a friend and help ya out.
 
Offroadnutz

Offroadnutz

Rank VI
Launch Member

Member III

3,257
Texas/Missouri
First Name
Steven
Last Name
Mmm
Member #

21045

Jackedupoffroad said:
I'm a little late to the party, but Id be happy to weld them up for you if you havent gotten them done already. . Located in a Plano. Not sure when with the current state of the nation, but when things clear up I'd be happy to make a friend and help ya out.
Click to expand...
What kind of experience do you have?
 
M Rose

M Rose

Local Expert
Mod Team
Member

Advocate III

5,584
Northeast Oregon, United States
First Name
Michael
Last Name
Rose
Member #

20990

Ham/GMRS Callsign
W7FSB
Service Branch
US ARMY Retired
Jackedupoffroad said:
I'm a little late to the party, but Id be happy to weld them up for you if you havent gotten them done already. . Located in a Plano. Not sure when with the current state of the nation, but when things clear up I'd be happy to make a friend and help ya out.
Click to expand...
Boosted is gone.
 
Offroadnutz

Offroadnutz

Rank VI
Launch Member

Member III

3,257
Texas/Missouri
First Name
Steven
Last Name
Mmm
Member #

21045

Couldnt see your pictures because I dont have a google account. But I do happen to need quite a bit of welding. Have been trying to decide wether to buy a welder and try and do it myself or pay someone else. Its been about 20 yr since I welded so im not to confident in my skills. Lol
I see you are not to far from me either so maybe we can work something out.
 
You must log in or register to reply here.
Top Bottom